Solar panels lose a little output every year, and for the panels themselves the yearly loss is small. That loss is slow and steady. If your system dropped a lot in one year, aging is almost never the reason, and it is worth finding out what is.
What the research says about normal degradation
The best public data comes from the National Renewable Energy Laboratory (NREL). After reviewing about 2,000 measured rates, its PV lifetime research puts the median loss for crystalline silicon panels at 0.5% per year. A long tail of lower-quality products pulls the average up to 0.8% per year.
Whole systems lose a bit more than panels alone, because wiring, inverters and dirt add their own losses. NREL's study of inverter data from thousands of U.S. systems found a median system loss of about 0.75% per year, and 90% of systems lost less than 2% per year.
Put simply: a healthy system makes a little less each year, and the change is so small you would barely see it from one year to the next. That is the baseline to compare your own numbers against.
What that looks like over 10 and 25 years
Here is a worked example, not a promise. Take a system that made 10,000 kWh in its first full year. At the NREL panel median of 0.5% per year from the PV lifetime research, it would make roughly 9,500 kWh a year after ten years. At the system median of 0.75%, closer to 9,250 kWh.
Over 25 years, the same math lands somewhere around 81% to 88% of the starting output, using the NREL medians above. The panels keep working after that. They just produce less, which is why a 20-year-old system can still be worth keeping and maintaining instead of tearing off.
Many panels also lose a little more in their first months of sun than in later years. That early dip is a known effect called light-induced degradation, and it is one reason the first-year line in most warranties is lower than the rest.
What speeds up degradation
- Heat: NREL found systems in hotter climates lose output faster, about 0.88% a year versus 0.48% in cooler ones. Most of Texas and Florida sit on the hot side.
- Heat plus humidity: A UNSW study projected the fastest degradation in hot, humid regions, while hot but dry areas fared better. Think Houston and Florida more than West Texas.
- Panel quality: The long tail of weaker products is what pushes the NREL average above the median. Tier 1 brands with a linear performance warranty usually spell out exactly how much they may lose.
- Physical damage: Hail impacts, microcracks from foot traffic, or panels flexed during a careless removal can cause losses that do not resemble normal aging at all.
- Poor installation: Loose connectors, water in junction boxes and wiring rubbing on the racking cause problems that grow over time and are often blamed on the panels.
Degradation is slow. Most big drops are something else
This is the part most articles skip. Even in a hot climate, normal aging takes years to add up to a noticeable loss. If your production fell by a tenth, a fifth or more compared with last year, the panels did not suddenly get old. Something changed.
The usual suspects are a failing inverter, one or more microinverters offline, a tripped breaker, a string that stopped producing, new shade from a growing tree, or heavy dirt and pollen. See what to check when your solar inverter is not working, and whether your panels need cleaning at all.
After a storm, add hail to the list. Damage is not always visible from the ground, so it helps to know how hail affects solar panels before you assume the output loss is just age.
Here is an example of how this plays out. Say a home in Katy shows a clean production curve on sunny days, but the yearly total is well below the year before. The panel-level view shows three panels at zero. That is not degradation. That is three microinverters or a connector to repair, and the rest of the system is fine.
The difference matters for your wallet. Normal degradation is not something you can fix or claim. A fault usually is fixable, and a panel that loses far more than its warranty allows may be a warranty claim.
How to check if your system is below where it should be
- Pull your yearly totals. Open your monitoring app and write down total kWh for each full year. Our guide on how to read a solar monitoring app shows where to find them.
- Compare year to year, not month to month. Seasons and weather swing monthly output a lot. Compare the same months or full years. A healthy trend is flat with a small slope down.
- Get a fresh estimate. Enter your address and system size in NREL's free PVWatts calculator. It gives a typical-year estimate. A system far below it, year after year, deserves a look.
- Look panel by panel if you can. Microinverter and optimizer systems show each panel. One panel far below its neighbors points to a panel, connector or microinverter problem, not aging.
- Check the obvious. Breakers in the main panel, error lights on the inverter, new shade, and a monitoring gateway that stopped reporting. A dead app is not always a dead system.
What your warranty actually covers
Most panels come with two warranties: a product warranty for defects and a performance warranty for output. The performance warranty sets a minimum output the panel should still deliver each year. Most brands now use a linear schedule that drops a fixed amount per year, as this solar warranty guide explains.
Find the warranty sheet for your exact panel model and note two numbers: the guaranteed output at the end of year one and at the end of the warranty term. If a panel tests below its line, that is a claim, not normal wear.
Keep in mind that a performance claim usually needs a panel-level test, not just a lower bill. Bills move with your usage, your rate plan and the weather, so they are a poor way to measure panel health. Monitoring data and on-site testing are what a manufacturer will accept.
To make a claim, the manufacturer will usually want proof: monitoring history, test results and photos. If the company that installed your system has closed, an independent technician can gather that evidence. That is what our project rescue work covers.
When to call a technician
- Production dropped by a tenth or more versus the same period last year, with similar weather.
- One or more panels or microinverters show zero or far below their neighbors.
- The inverter shows error codes or lights you cannot clear.
- Your system is well below its PVWatts estimate for two years or more.
- You had hail or a major storm and output changed right after.
- Your bill went up and you are not sure if it is the system or your rate plan. Our guide on why solar panels may not be saving money anymore helps sort that out.
Frequently Asked Questions
NREL research on PV lifetime puts the median at about 0.5% per year for crystalline silicon panels, with an average of 0.8% when lower-quality products are included. Whole systems, which include inverters and wiring, showed a median loss of about 0.75% per year in NREL's fleet study.
Heat does speed it up. NREL found systems in hotter climates lost output faster than those in cooler climates, and research from UNSW points to hot, humid regions as the hardest on panels. Good ventilation under the panels and quality equipment help, but some extra loss is expected.
At the NREL median rates, a system usually lands somewhere around 81% to 88% of its starting output after 25 years. Your panel's performance warranty states the minimum the manufacturer guarantees, so check the sheet for your exact model.
Normal aging cannot be reversed, but most sudden output losses are not aging. Inverter failures, offline microinverters, damaged wiring, shade and dirt can all be found and fixed. A panel that degraded beyond its warranty line may qualify for replacement.



