Solar Panel Removal & Reinstallation in Carrollwood, FL

America’s #1 Choice for Energy Independence

We handle removal, storage, and reinstallation — coordinating with your roofer so your project runs smoothly from start to finish.

By submitting or calling, you consent to receive calls and SMS from The Light Group USA at the number provided, including via auto-dialer or pre-recorded messages. Consent is not required for purchase. Msg/data rates may apply. Reply STOP to opt out. See our Privacy Policy.

Get Started

Protect your roof and your solar investment

Let professionals handle your solar panel removal the right way.

By submitting or calling, you consent to receive calls and SMS from The Light Group USA at the number provided, including via auto-dialer or pre-recorded messages. Consent is not required for purchase. Msg/data rates may apply. Reply STOP to opt out. See our Privacy Policy.

Removal & Reinstall

Panel removal and reinstall in Carrollwood

Carrollwood grew up around Lake Carroll, and most of the neighborhoods off Dale Mabry Highway were platted long before anyone put an array on a Hillsborough County roof. The shingles under those panels are frequently on their second or third life. When the reroof finally gets scheduled, the solar has to come off first, and that turns out to be a separate trade from either roofing or solar sales.

Almost nobody plans for it. A homeowner collects three roofing quotes and all three end the same way: we do not touch solar. Then the original installer's number rings to a recording. The roof is a roofing problem, the array is a solar problem, and the two companies will not schedule around each other. Removal and reinstallation is the work that sits in that gap.

Carrollwood sits roughly seven kilometers inland, so salt is not the issue here. Heat, oak litter and central Florida lightning exposure are. What matters more on a removal is the lot itself: mature canopy, narrow side yards and deed-restricted frontage leave little room to stage sixty or seventy modules for two or three weeks. Where they go gets decided before anyone climbs a ladder.

Most Carrollwood addresses are unincorporated Hillsborough County, which means the permit for a removal and reinstallation goes through the county rather than a city building department, and a county inspector signs off at the end. None of this is emergency work. It is planned around your roofer's calendar, and we cover it from Orlando and Tampa on a date set in advance.

What We Check

On a Carrollwood removal we get these right

The roof drives the calendarNothing gets scheduled until your roofer commits to a tear-off date. We build the removal backward from it so the deck is clear the morning the crew arrives, and we hold the reinstall until the new roof is dried in, inspected and actually finished, not almost finished.
Shutdown and labeling before anything movesThe array stays energized until it is deliberately not. DC is opened at the inverter or the rapid shutdown device, the AC breaker is locked out, and every module, rail and home run is labeled by row and position so the system goes back exactly the way the string design intended.
Where the panels live in the meantimeA reroof in a Carrollwood subdivision can run two or three weeks. Modules go on padded racks, on edge, off the ground and out of the driveway you still need to use. They are never stacked face down on a garage floor and never leaned against a fence.
Microcracks come from handling, not weatherGlass survives hail better than it survives a bad lift. Panels are carried at the frame corners, never dragged by the long rail, never set on the glass, never stacked without separators. A cracked cell does not announce itself; it shows up months later as a string that quietly underproduces.
Reinstall is where a roof gets ruinedEvery new penetration has to land in a rafter, not in the sheathing between them, and flashing goes under the course above rather than sealed on top with a bead of caulk. Clamp torque follows the module spec sheet. Sealant is a backup, never the waterproofing.
Hillsborough County permit and reinspectionRemoval and reinstallation generally needs a permit in Florida, and for unincorporated Carrollwood that is Hillsborough County rather than a city desk. We confirm the jurisdiction by address before quoting, and the array is not called finished until the electrical reinspection is closed out.
FAQ

Solar service in Carrollwood — common questions

Yes, in almost every case. Roofers cannot tear off and re-deck under a mounted array, and most will not warranty a roof they could not fully access. The panels, rails and attachments all come off, the roof is replaced, and the system goes back on new penetrations. Partial removal is only realistic when a single slope is being repaired.

Hillsborough County does, not the City of Tampa. Large parts of Carrollwood are unincorporated, so the building and electrical permits for a solar removal and reinstallation are pulled and inspected at the county level. We verify jurisdiction from the parcel address before the job is scheduled, because it changes the inspection sequence and the lead time.

Usually as long as the roof takes, which for a typical Carrollwood reroof runs two to three weeks. Removal is normally one day, the roofing work follows your roofer's schedule, and reinstallation is another day or two once the new roof passes inspection. You are not producing during that window, so both dates are set up front.

They are three separate warranties and they behave differently. Module and inverter manufacturer coverage usually survives a professional removal and reinstallation, but workmanship coverage from the original installer typically does not follow a third party. Your new roof warranty comes from the roofer and can be voided by penetrations flashed incorrectly. Each attachment is documented.

Yes. Orphaned systems are common, and the first step is documentation rather than demolition. We identify the module and inverter models, map the string layout, photograph every attachment and label the rows before anything is unbolted, so the array can be rebuilt correctly even though the original design drawings no longer exist anywhere.